Cabinet Refacing in Windermere, Edmonton
Cabinet refacing in Windermere is a kitchen renovation that replaces your existing cabinet doors, drawer fronts, and end panels with brand-new components in a 2026 profile, then re-veneers the visible cabinet box faces to match. Your carcasses, layout, plumbing, and granite or quartz countertops stay in place. A typical Windermere reface in 2026 takes 7 to 10 working days and costs $14,000 to $28,000, versus $75,000 to $150,000 for a full kitchen replacement.
iPaint Painting has refaced kitchens across Windermere Estates, Cavanagh, Hawks Ridge, Glenridding Heights, and Keswick on the River since 2011. Owner-led by Mourad. Call 780-938-9555 for a free in-home measure and door-sample visit.
Project
Warranty
156 Reviews
Doors
Why a Windermere Homeowner Picks Refacing Over Refinishing
Both keep your layout. Only refacing gives you brand-new doors in a modern 2024-2026 profile. Here is the side-by-side.
Cabinet Refacing
The renovation route. New doors. New face.
- +Doors and drawer fronts are replaced entirely with new components
- +Cabinet box faces are re-veneered to match the new doors
- +You change the door profile (raised panel to shaker, arched to slab, etc.)
- +You can change the material (melamine to solid maple, oak veneer, white oak)
- +Project runs 7-10 days, kitchen unusable 2-3 days
- +Windermere range: $14,000-$28,000
Cabinet Refinishing
The cosmetic route. Same doors. New colour.
- oExisting doors are stripped, sanded, and spray-painted
- oYou keep the same door profile the builder installed
- oMaterial stays whatever it was originally
- oAny dents, dings, or worn edges on the doors stay
- oProject runs 5-7 days, similar disruption
- oWindermere range: $7,000-$14,000 (roughly half of refacing)
Rough rule of thumb: if your 2008 Windermere builder installed raised-panel maple with arched uppers and you want a 2026 flat shaker or slab kitchen, the only honest answer is refacing. If your shaker doors are already shaker and you just want them white instead of espresso, refinishing is the smarter spend.
Brand-New Faces on Every Visible Surface
A typical Windermere reface swaps 25-45 doors, 8-15 drawer fronts, 4-7 end panels, and 1-2 islands. Here is every piece that gets a new face.
New Doors (25-45)
Custom-built doors in flat shaker, recessed shaker, or slab, sized to your existing openings within 1/32 inch tolerance.
New Drawer Fronts (8-15)
Matching drawer fronts cut to height. Existing drawer boxes are kept unless you choose dovetail upgrades.
Box Re-Veneer (3/4 mm)
Every visible face frame and box edge gets a fresh wood veneer skin that matches the new door material exactly.
New End Panels (4-7)
Decorative end panels on exposed cabinet sides, dishwasher panels, fridge cabinet panels, all replaced to match.
Island Faces (1-2)
Windermere islands run 9-14 feet. We reface every visible side, including the seating-side back panel and waterfall returns.
BLUM Soft-Close Hinges
Every door is rehung on new BLUM Compact 38N or Clip Top hinges with adjustable soft-close dampening.
Modern Hardware
Unlacquered brass bar pulls, matte black knobs, brushed nickel cup pulls, or integrated channel pulls routed into the door edge.
Butler & Walk-In Pantry
Windermere homes typically have both a butler pantry and a walk-in pantry. Both get refaced to match the main kitchen for visual continuity.
Not sure if your cabinets are reface candidates? Particle-board boxes from a 1990s build sometimes don't hold new veneer well. We'll check the carcass condition on the in-home visit. If refacing isn't the right call, we'll honestly recommend cabinet refinishing or full replacement instead.
The 7-10 Day Windermere Reface Sequence
No demo trucks in the driveway. No granite removal. No re-plumbing. Just doors off, faces re-skinned, new doors on.
In-Home Door Sample Visit
Mourad brings physical door samples (shaker, slab, white oak, painted maple) to your Windermere home so you compare against your countertops, backsplash, and flooring in real lighting.
Precision Field Measure
Every door opening measured to 1/32 inch with a digital caliper. Drawer openings recorded separately. End-panel dimensions captured. Numbers go straight to fabrication.
Custom Door Fabrication
Doors and drawer fronts are built in our shop or sourced from a Canadian door specialist. Lead time typically 3-4 weeks before install begins.
Day 1: Doors Off, Boxes Prepped
Old doors and drawer fronts come off. Hinge cups filled. Cabinet box faces scuff-sanded and cleaned for veneer adhesion. Hardware is bagged for disposal or donation.
Days 2-4: Veneer + Hang
Box faces get the new wood veneer skin applied with contact adhesive and rolled flat. New doors are hung on BLUM soft-close hinges. End panels installed. Drawer fronts attached.
Days 5-10: Hardware + Walkthrough
Pulls, knobs, and channel pulls go on. Every door is aligned within 1 mm of its neighbour. Final walk with you against a printed punch list. 5-year warranty activates.
Why Windermere Picks iPaint for Cabinet Refacing
Refacing is fabrication plus finish carpentry plus design. We do all three under one roof, no subcontracted door installers.
Door Styles That Sell in Windermere
Flat shaker with a 2.25 inch rail. Slab with a routed channel pull. Recessed shaker with a 1.75 inch rail. Two-tone schemes where the island goes Kendall Charcoal against Chantilly Lace perimeter cabinets. These are the looks moving in Cavanagh and Hawks Ridge right now.
Mourad Personally on Site
The owner runs every reface. He does the door-sample visit, the field measure, and the final walk personally. With 15+ years of cabinet work and Painter and Decorator Certification, he is the one accountable when something doesn't line up.
Your Granite Stays Put
Full kitchen replacement means pulling out the slab, fabricating new templates, and refitting. That's $8,000-$15,000 in fabrication alone on a Windermere island. With refacing, your existing granite or quartz never moves.
One-Sixth the Cost of Replacement
Full kitchen demolition and rebuild in a Windermere Estates executive home runs $75,000-$150,000 once you factor in cabinets, stone fabrication, plumbing, electrical, lighting, and drywall patch. Refacing delivers a new-kitchen look for $14,000-$28,000.
5-Year Written Warranty
Every door, every veneer seam, every BLUM hinge, every hardware fitting. If anything we installed fails inside 5 years, we come back. Written, signed, mailed to you on completion day.
Lives Around Your Family
Off Anthony Henday Drive, school drop at Mother Margaret Mary Catholic High School, swim lessons at Edmonton Triathlon Club, a teenager who needs her kettle. Our crew works clean, contains dust, and leaves the kitchen functional every evening past the box-prep phase.
Windermere Refacing Cost Ranges
Honest numbers based on actual recent Windermere projects. Final quote is fixed-price after the in-home measure, no allowances or change-order games.
Refacing pricing scales with door count and material. Rift-cut white oak veneer typically adds 15-25% over painted maple. Brass hardware adds roughly $40-$90 per door over basic chrome. Every quote is itemized, written, and fixed-price. Book your in-home measure or call 780-938-9555.
Why Windermere Kitchens Are Refacing Candidates Right Now
The 2005-2018 Build Window
The Windermere master-planned community in southwest Edmonton opened in 1998 but most of the housing stock came online between 2005 and 2018. Subdivisions like Windermere Estates, Cavanagh, Hawks Ridge, Glenridding Heights, Glenridding Ravine, Keswick on the River, and The Uplands all came in during the same era, which means thousands of Windermere kitchens share the same builder spec: raised-panel maple uppers, slab drawer fronts, granite countertops, polished chrome hardware, and a 9 to 14 foot island. That spec looked premium in 2010. In 2026 it reads dated, even on homes worth $1.2M+.
The Door Profile Is the Tell
Walk into any kitchen built in Windermere Estates between 2007 and 2012 and the same details give the age away: a 3-inch raised centre panel on the doors, an arched top on the over-fridge cabinet, a thick crown moulding stack at the ceiling, and chunky 4-inch brushed-chrome bar pulls. Refacing is the only way to swap that profile for a 2026 look (flat shaker, slab, recessed shaker) without tearing out the boxes. Refinishing keeps the dated profile and just changes the colour, which often makes the dated detailing more obvious, not less.
Coordinating With Existing Granite and Quartz
Most Windermere kitchens were built with granite countertops in Uba Tuba, Black Pearl, or Santa Cecilia. Some later builds went Caesarstone or Silestone quartz in white or grey. Replacing the cabinets means pulling the stone, which means new templates, refabrication, and re-install at the $8,000-$15,000 mark on a Windermere island alone. Refacing leaves your stone where it sits. We bring door samples in person so you can hold a Chantilly Lace shaker door right against your Black Pearl granite and confirm before fabrication starts.
Still trying to decide between refinishing, cabinet painting, or refacing? Call 780-938-9555. The in-home visit is free and Mourad will tell you straight which one fits your kitchen.
What a Windermere Reface Project Actually Includes
Every Windermere reface quote breaks out the line items. Here is the standard scope for a mid-size kitchen with one island.
- 25-32 new doors built to your specified profile and material
- 8-15 new drawer fronts sized to existing openings
- 4-7 new end panels for exposed cabinet sides, dishwasher, and fridge cabinet
- 3/4 mm wood veneer on every visible face frame and box edge
- Island refacing on all four visible sides plus any waterfall returns
- BLUM Compact 38N or Clip Top hinges on every door with adjustable soft-close
- Hardware fitting in your chosen finish (brass, matte black, brushed nickel, channel pull)
- Old door disposal or donation to Habitat for Humanity ReStore
- Daily clean-up, ZipWall dust containment, drop sheets over flooring and adjacent counters
- Final alignment within 1 mm door-to-door and 1/32 inch reveal
- 5-year written workmanship warranty, signed and delivered
As Mourad always says: "We treat your home like ours. The kitchen leaves cleaner than we found it, the same way we'd want our own kitchen handled."
If your kitchen is so badly worn that even refacing won't save it, we'll say so. If you want walls done too, our interior painting team can run in parallel. If the woodwork in the rest of the house needs attention, we can fold in stain and lacquer work in the same engagement.
Refacing Across Windermere & Southwest Edmonton
We work every Windermere subdivision and the broader SW Edmonton corridor along Anthony Henday Drive and Terwillegar Drive.
Primary Service Area
Windermere Subdivisions We Reface In
Greater SW Edmonton
Serving the Windermere Master-Planned Community
Centred near Windermere Common and Currents of Windermere, with reface work running across every subdivision inside the T6W and T6X postal codes.
Before & After: Windermere Door Style Swaps
Real Windermere refacing projects. Same boxes, same granite, completely new doors and faces.
BeforeAfter
BeforeAfter
BeforeAfter
BeforeAfterIf Refacing Isn't the Right Fit
Sometimes refinishing is the better spend. Sometimes you want walls done too. Here is the full list.
Cabinet Refacing FAQs - Windermere
The five questions Windermere homeowners ask most before booking a reface.
What is the difference between cabinet refacing and cabinet refinishing for a Windermere kitchen?
Cabinet refinishing strips, sands, and spray-paints your existing doors and boxes. You keep the same raised-panel or arched profiles that came with your 2005-2015 Windermere build, just in a different colour. Cabinet refacing replaces the doors, drawer fronts, and end panels entirely with brand-new components, plus we re-veneer the visible faces of the boxes. The structural carcasses stay in place. Refacing is the right call when the door profile itself looks dated, which is the case in most Windermere homes built with raised-panel maple. Refinishing is the right call when the profile is fine but the colour or finish wear needs a refresh. Refacing costs roughly 1.5x to 2x more than refinishing on the same kitchen, but you end up with new doors in a 2026 style.
How much does cabinet refacing cost in Windermere?
A typical Windermere kitchen reface runs $14,000 to $28,000 depending on door count, material, and hardware spec. A mid-size kitchen in Glenridding Heights or Cavanagh with 25-32 doors and one island lands at $14,000-$19,000 in solid maple shaker. A larger executive kitchen in Windermere Estates or The Uplands with 33-45 doors, two islands, and a butler pantry runs $19,000-$28,000, especially when the door material is rift-cut white oak veneer or a two-tone scheme. Compared to full cabinet replacement at $75,000-$150,000 (cabinets, granite or quartz, plumbing, electrical, drywall patching), refacing delivers a kitchen that looks brand new at a fraction of the cost and disruption.
How long does cabinet refacing take in a Windermere home?
Most Windermere refacing projects run 7 to 10 working days from door removal to final adjustment. Your kitchen is unusable for roughly 2 to 3 of those days while the boxes are re-veneered and the new doors are hung. Drawer fronts and end panels go on in parallel. Compare that to gutting and rebuilding the kitchen, which typically takes 6 to 12 weeks in Windermere once you account for cabinet lead times, granite or quartz fabrication after the boxes are set, plumbing rough-in, and final inspection.
Which door styles and materials are most popular for Windermere cabinet refacing in 2026?
The dominant 2024-2026 looks we install in Windermere are flat shaker (a 2.25 inch rail with a recessed flat panel), slab (a single flat plane, often with an integrated channel pull), and recessed shaker with a thinner 1.75 inch rail. Materials trending in Windermere right now are solid maple painted in Benjamin Moore Chantilly Lace, Cloud White, or Kendall Charcoal; rift-cut white oak veneer for the warm modern look; and quarter-sawn oak for transitional kitchens. Hardware is moving away from polished chrome toward unlacquered brass, matte black, brushed nickel, and integrated channel pulls that disappear into the door edge.
Do you reface cabinets in all the Windermere subdivisions, including Cavanagh, Hawks Ridge, and Keswick on the River?
Yes. iPaint Painting refaces cabinets throughout the Windermere master-planned area in southwest Edmonton, including Windermere Estates, Windermere Heights, Cavanagh, Hawks Ridge, Glenridding Heights, Glenridding Ravine, Keswick on the River, and The Uplands. We are familiar with the housing stock built between 2005 and 2018 in this area, the original cabinet specs from the major Windermere builders, and the trades coordination required for triple-garage executive homes off Anthony Henday Drive, Windermere Boulevard, 184 Street SW, and Terwillegar Drive. Call 780-938-9555 to confirm scheduling for your subdivision.
Ready for a New Kitchen Without Gutting the Old One?
Mourad brings door samples to your Windermere home, measures every opening, and gives you a fixed-price quote on the spot. No deposit to book the visit. No pressure.